Forum Replies Created
-
Posts
-
Hello,
I would recommend purchasing mastic board and screwing on top of your existing counter top first, and then applying the tile. This will insure you have the right surface for the tile to stick to. This may raise the over height of the counter top by a ¼” or so, but in the long run it will be more beneficial. Your can use the mastic board on the top as well as the edges. Obviously you will have to remove the sink, faucet and cook top first, then apply the mastic board make your cut outs and then tile.Dominic Anfossi
Visit http://www.MyPlumbingSupplier.com for more tips and product information.If the area where you removed the tile is wet, then there is a very good chance other areas are wet as well. The best way to eliminate future problems, like mold, termites and tiles falling off would be to remove all the tile. At that point you can determine if there is any additional damage and make repairs.
When you redo the bathroom walls, make sure you use green board, and then tile on top of that. Its a big project, but it will be easier now, since you know there is some damage rather then waiting and potentially have bigger issues.
Dominic Anfossi
Visit http://www.MyPlumbingSupplier.com for more tips and product information.If your toilet isnt filling up, then the fill valve should be replaced. This is a very easy fix and should cost under $20.00. Attached I have included a link for you to look at. You dont need to go with this manufacturer, but the info will be the same for just about all of them. http://www.brasscraft.com/Default.aspx?Page=Products.aspx
Remeber, always shut off the water before you start working.
Dominic Anfossi
http://www.MyPlumbingSupplier.comAs the previous poster pointed out. Using backboard will create its own set of problems/head aches. Mortar is the best way to proceed. This will give you a nice smooth/seamless surface to place your tiles on. Sometimes what is simple isnt the best.
Dominic Anfossi
http://www.MyPlumbingSupplier.comIf your faucet has supply hoses connecting it to the water supply valves (as opposed to copper lines), go to your local plumbing supplier and purchase 1 new hose(under $10.00). Then switch the cold water line with the new hose and turn water on. Do the same for the hot water line. If water comes out then you know you need to replace both hoses. If you still dont have water, then there is something wrong with the faucet.
In most cases, on single leaver faucets they have a ceramic disc cartriged located under the handle. Turn off the water, remove the handle set screw and with a pair of pliers you can remove the cartridge. Take that along with the faucet brand to your local plumbing supplier and for under $20.00 you can replace it. If this doesnt work, I recommend purchasing a new faucet rather then having a plumber come in and try the same things I just recommended. Good luck, and remember, always shut off the water first.
Dominic Anfossi
http://www.MyPlumbingSupplier.comAs previously stated, if you use silicone (preferably clear)and tighten the drain/pipe you should be fine. Keep in mind in most cases vessel sinks dont have overflow drain holes in them, so you wont be able to use your existing drain. You generally need a drain that is designed for a vessel sink. Installing the sink isnt that hard, and doesnt required a plumbing, sure they can get it done quickl. But at what cost? If you need a vessel sink drain check out the Danze model D495082, this is a very good item and very reasonablly priced.
Dominic Anfossi
http://www.MyPlumbingSupplier.comWhen redoing a tile shower floor using mortar over the membrane will allow you to slightly slope the floor towards the drain. Sloping the floor slightly towards the drain allows you to have proper drainage in the shower, and also helps to prevent standing water. Using backerboard may seems to be easier, however backerboard is rigid and will not allow you to create the desired slope.
Dominic Anfossi
http://www.MyPlumbingSupplier.com
